Can’t Perform Wavlink WiFi Extender Setup?

Various users are struggling to set up the Wavlink WiFi extender. Are you also unable to do Wavlink setup? Well, we are assuming that you are experiencing this issue because you referred to the wrong source for info about the process. But, worry not. In this guide, we have talked about two methods in detail through which you can easily do Wavlink set up.

How to Do Wavlink Setup Using Wi-Fi Protected Setup Method?

Using the WPS method is the easiest way to extend your host network. Follow the steps given below to do Wavlink set up using this method:

• Plug your host router into a wall socket and turn it on.
• Make sure that your extender is plugged in and powered on too.
• Press the WPS button on the host router.
• After 2 minutes, press the WPS button on the Wavlink WiFi extender.
• Wait for the LED to turn solid blue.

For your information, this is an indication that the WPS connection is successful.
Now, the extender will automatically find the signal of the router and extend it.

Did You Know?

• To minimize signal interference, choose a location for the extender which is far away from baby monitors, microwaves, cordless phones, and Bluetooth devices.
• The location that you will choose should also be within the range of the existing host router. Otherwise, the performance of your extended network will get impacted.
• Some ISP gateways disable the WPS function by default. In case the WPS connection fails in your case, it is recommended that you log in to the management page to set up Wavlink WiFi extender using another method.

How to Configure Wavlink WiFi Extender in AP Mode?

The basic requirement to execute this method is the use of an Ethernet cable to connect the extender and router. Given this, follow these instructions to set up Wavlink extender in AP mode in a hassle-free manner:

Hardware Connections

• Connect the POE IN port of the unit to the POE port of the converter with a cable.
• Then, connect the LAN port of the extender to the LAN port of the router.
• Plug the power adapter into a wall socket.
• Press the power button.

AP Mode Installation

• Switch on your PC and connect it to the WiFi of the Wavlink extender.
• Load a browser and enter 192.168.10.1, ap.setup.com, or wifi.wavlink.com.
• Press the Enter key.
• Enter the default password as admin on the login screen.
• After logging in, click the AP button.
• Enter the settings such as SSID and WiFi password.
• You will also be asked to enter the Security Type.
• Click the Apply button. Please wait for a few seconds.
• At last, return to the WLAN and reconnect to the WiFi.

With that, you will be able to complete the Wavlink set up process in Access Point mode. In case, you are still stuck with setup issues, then refer to the following section.

Still Can’t Set Up Wavlink WiFi Extender? Here is What Need to Do!

Use a Non-Damaged Cable

Before trying any other solution, check if the Ethernet cable used to connect the range extender to the host router:

• Is worn out
• Has Cuts

In case any of these things is true, then it is recommended that you use a new cable to connect the networking devices.



Choose Any Other Wall Socket



Another reason why you cannot do wifi.wavlink.com setup is because you did not use a damage-free wall socket. There are two things that you can do in this case:

• Call up an electrician and get your current wall socket repaired.
• Use any other wall socket to supply power to your networking device.

Now check if you are able to set up your networking device with ease or not. In case you are still not able to, then you should pay attention to the last tip.

Input the Right Address

See if the web address that you have entered is correct or not. In case, it is not, then enter it again. For your information, the Wavlink wireless range extender has two web addresses, i.e. wifi.wavlink.com and ap.setup.

It is recommended that you avoid entering the addresses like this:

• Wifi.wavlink.com as wifi.wavlink.com setup or wifi wavlink com setup
• Ap.setup as ap setup